日韩视频在线这里只有精品,国产黄色片一区二区视频 ,亚洲不卡顿在线免费视频

當前位置：首頁 > 產品中心 > 產品類別 > 汽車尾氣治理-三元催化清洗劑汽車尾氣治理

三元催化清洗劑

1. 有效清除三元催化器表面的積碳及殘留物。

2. 恢復三元催化器的凈化功能，降低尾氣排放。

3. 提升燃油燃燒效率，提高冷車啟動性能，降低油耗，恢復發動機動力。

4. 延長三元催化器的使用壽命，減少維護綜合成本。

產品說明

優道三元催化高效清洗劑

品牌：UD優道

系統：進排氣系統

產品編號：UD-01.265/325ml

企業標準：Q/YKJH 8

產品僅供4S店使用

產品特點：

1. 有效清除三元催化器表面的積碳及殘留物。

2. 恢復三元催化器的凈化功能，降低尾氣排放。

3. 提升燃油燃燒效率，提高冷車啟動性能，降低油耗，恢復發動機動力。

4. 延長三元催化器的使用壽命，減少維護綜合成本。

使用方法：

1、啟動發動機至正常工作溫度，

2、用專用油門固定器將引擎轉速固定在2500轉

3、尋找、拆開節氣門后的真空管（有真空吸力），靠近節氣門第一個管口最佳，

4、把產品瓶口打開連接在專用清洗設備上（或倒入設備鐵罐中），并把設備出液透明軟管與汽車的真空管對接，

5、打開設備開關，將流量調整開關調到產品成滴入裝狀進入真空管為正確，清洗時間為25-30分鐘最佳，

6、整瓶產品用完，除碳時間完成，拔出連接汽車真空管接頭并恢復原狀，

7、將油門固定器拆下，以每500轉/10秒輕緩加油，逐漸加至3000轉，以稍快速度重復上述動作。

8、待進排氣聲順暢時再排碳15分鐘，除碳中及排碳時絕不可以重踩油門，排碳后必須進行路試。

Product features:

1. Effectively remove the carbon deposition and residue on the surface of the ternary catalytic converter.

2. Restore the purification function of the three-way catalytic converter and reduce the exhaust emission.

3. Improve fuel combustion efficiency, improve start-up performance of cold vehicle, reduce fuel consumption and restore engine power.

4. Extend the service life of three-element catalytic converters and reduce the comprehensive maintenance cost.

Usage:

1. Start the engine to the normal operating temperature,

2. Fixed the engine speed at 2500 revolutions with special accelerator fixator

3. Look for and open the vacuum tube behind the throttle (with vacuum suction). It is best to be close to the first pipe opening of the throttle.

4. Open the product bottle mouth and connect it to the special cleaning equipment (or put it into the equipment tin), and connect the device's liquid outlet transparent hose to the vacuum tube of the car.

5. Turn on the device switch, and adjust the flow rate adjustment switch to the product to drip into the vacuum tube. The cleaning time is 25-30 minutes.

6. When the whole bottle of product is used up, the decarbonization time is completed, and the vacuum tube connector of the car is pulled out and restored to its original state.

7. Remove the accelerator fixator and gently refuel every 500rpm / 10s, gradually add to 3000 RPM and repeat the above action at a slightly faster speed.

8. When the inlet and exhaust sound is smooth, the carbon shall be discharged for another 15 minutes. In addition, the gas pedal shall not be pressed again when the carbon is removed and the road test shall be conducted after the carbon is discharged.